Getting Started

Midwest Cover Crops Council (MCCC-111)

Michigan State Extension (CC-05)


This publication is intended to provide a starting point for farmers who are new to growing cover crops. With experience, farmers may fine-tune the use of cover crops for their systems.

Introduction

The following recipe provides an introductory approach to integrating a cover crop into a wheat rotation with soybean or corn. Planting oat and radish cover crops after wheat (see Figure 1) and ahead of a soybean or corn cash crop is an easy way to introduce cover crops into your rotation because these cover crops both winterkill and add important diversity to agricultural fields.

Figure 1. A growing oats and radish mix (Paul Gross)
Figure 1. A growing oats and radish mix (Paul Gross)
Planning and Preparation
  • Planning—Educate yourself. Start small. Be timely. Prioritize management based on your purpose and objectives.
  • Wheat variety and planting—No modifications to wheat variety and planting are required for the successful use of cover crops after wheat harvest.
  • Residual wheat herbicides—Oats and radish are tolerant of most wheat residual herbicides, and few restrictions apply unless grazing is being considered. Oats and radish may be sensitive to Osprey® and PowerFlex®, and while data is limited, possible injury may result. See Weed Control Guide for Field Crops (in Resources section) for more details.
  • Seed purchase—Order cover crop seed early. Named varieties generally perform more predictably and can produce substantially more growth than variety not stated (VNS) seed but are more expensive. VNS seed may be a good option when purchased from a reputable dealer if it has been cleaned, tested for germination, and has a seed tag. For cover crop radishes (daikon type), be sure to purchase a single variety from a reputable seed dealer since mixed varieties may have unpredictable emergence or immediately flower and produce seed rather than producing the desired large amounts of biomass and roots.
Summer/Fall Work
  • Wheat harvest—Harvest wheat at the normal time in fields where a mix of oats and radish will be planted. If residue levels are high, consider removing straw or using light tillage to improve seed-to-soil contact.
  • Timing of planting—Plant oats and radish any time in August after wheat harvest. Planting a cool-season annual, such as radish, prior to August is not recommended as it may result in flowering and seed production instead of quick coverage and biomass accumulation, which is the desired goal for this cover crop. Use the Cover Crop Selector Tool (in Resources section) for precise seeding dates for your county because both proximity to the Great Lakes and latitude influence planting dates.
  • Planting method—Drill to a depth of 0.50–0.75 inch or broadcast with light incorporation. Note that disturbance of soil, if any, should be light since excessive disturbance of wheat stubble may negate any benefit of the cover crop. See Recommended Cover Crop Seeding Methods and Tools (in Resources section) for more details.
  • Seeding rate in oats/radish mix—Mix seeds prior to planting at the following rates. Drilled: oats, 30–60 lbs./acre; radish, 2–3 lbs./acre. Broadcast: oats, 35–65 lbs./acre; radish, 3–4 lbs./acre. See Cover Crop Choices Following Winter Wheat (in Resources section) for more information.
  • Tillage or no-tillage—To allow for adequate cover crop growth, it is best if no full-width tillage takes place until oats and radish have been killed by freezing temperatures. If tillage is used, it is usually better to wait until spring in order to maintain surface cover to prevent erosion.
  • Fertility or liming—If applying P, K, lime, or manure, complete the application and incorporation prior to seeding or apply to the growing oats and radish before the ground freezes. If injecting manure, low-disturbance injectors are available that will minimize damage to oats and radish. Surface application of liquid manure on top of the cover crop is not recommended. Surface broadcast of dry manure or litter should be done prior to seeding, but 4 tons or less can be applied to growing oats and radish with minimal damage provided it is evenly distributed. See the manure management publication (in Resources section) for more information on generally accepted practices for manure management and utilization.
Figure 2. Residue of oats/radish mix in early March (Eileen Kladivko)
Figure 2. Residue of oats/radish mix in early March (Eileen Kladivko) 
Spring Work
  • Starter fertilizer—No modifications to your typical fertilization program are required for planting soybean or corn after oats and radish use.
  • Termination—Oats and radish should both terminate by winterkill. However, mild winters and good snow cover sometimes allow overwintering of radish. If this occurs, radish is easily terminated with typical pre-plant herbicide applications.
  • Soybean or corn planting—It is usually best to no-till plant cash crops into the dead/dry or standing cover crop. Almost all modern planters and drills are fully capable of planting soybean or corn into an oat and radish cover crop. Check planting depth and seed furrow closure shortly after beginning to plant into the cover crop residue (see Figure 2) as usually some adjustments are needed.
  • Scouting—After soybean or corn planting, scout for crop emergence and population. Additionally, scout for weeds since cover crop residue can often delay emergence of annual weeds, which may delay the application of post-emergence herbicides.
Resources

Cover Crop Selector Tool —available from Midwest Cover Crops Council

Cover Crop Choices Following Winter Wheat (Michigan State University Extension)

Weed Control Guide for Field Crops (Michigan State University Extension Bulletin E0434)

Cover Crop Termination (Michigan State University Extension publication CC-01)

Recommended Cover Crop Seeding Methods and Tools (Agronomy Technical Note)— available from USDA–Natural Resources Conservation Service

Generally Accepted Agricultural and Management Practices for Manure Management and Utilization—available from the Michigan Department of Agriculture and Rural Development

Authors

Dean Baas, Michigan State University Extension (MSUE); Christina Curell, MSUE; Paul Gross, MSUE; Monica Jean, MSUE; Philip Kaatz, MSUE; and Elizabeth H. Schultheis, MSU (Note: This publication was adapted with consent from MCCC under a joint project to produce customized introductory guidance about cover crops for all member states/provinces.)

Reviewers and Contributors

Jerry Grigar, USDA–Natural Resources Conservation Service; Erin Hill, MSU; Eileen J. Kladivko, Purdue University; Anna L. Morrow, Midwest Cover Crops Council; Sieg Snapp, MSU

The Midwest Cover Crops Council (www.https://www.midwestcovercrops.org) aims to facilitate widespread adoption of cover crops throughout the Midwest by providing educational/outreach resources and programs, conducting new research, and communicating about cover crops to the public.
Funding for this project was provided by McKnight Foundation.

August 2019

The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable, sex, marital status, familial status, parental status, religion, sexual orientation, genetic information, political beliefs, reprisal, or because all or a part of an individual’s income is derived from any public assistance program. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program information (Braille, large print, audiotape, etc.) should contact USDA’s TARGET Center at (202) 720-2600 (voice and TDD). To file a complaint of discrimination write to USDA, Director, Office of Civil Rights, 1400 Independence Avenue, S.W., Washington, D.C. 20250-9410 or call (800) 795-3272 (voice) or (202) 720-6382 (TDD). USDA is an equal opportunity provider and employer. ©2019 by MCCC. All rights reserved.

Share

Midwest Cover Crops Council (MCCC-110)

Michigan State Extension (CC-04)


This publication is intended to provide a starting point for farmers who are new to growing cover crops. With experience, farmers may fine-tune the use of cover crops for their systems.

Introduction

This recipe provides an introductory approach to integrating a cover crop into a soybean-corn rotation. Planting a cereal rye cover crop ahead of corn is a way to introduce cover crops into your rotation. (Note: Cereal rye [Secale cereale] and annual ryegrass [Lolium multiflorum] are two different species and should not be used interchangeably.)

Planning and Preparation
  • Planning—Educate yourself. Start small. Be timely. Prioritize management based on your purpose and objectives.
  • Soybean variety and planting—If possible, plant the preceding soybean crop early and use an early maturity soybean cultivar. One strategy is to use your earliest-maturity-group soybeans on the fields where you plan to seed cover crops and plant those beans first.
  • Residual soybean herbicides—Cereal rye can be seeded and successfully established in the fall following most spring-applied residuals used in soybean. However, if cereal rye will be grazed or fed to livestock, check restrictions. See Weed Control Guide for Field Crops (in Resources section) for more details.
  • Natural Resources Conservation Service (NRCS) programs—Cover crops enrolled in the Conservation Stewardship Program (CSP) or Environmental Quality Incentives Program (EQIP) cannot be used for dual-purpose grazing.
  • Seed purchase—Order cereal rye seed early. Named varieties generally perform more predictably and can produce substantially more growth than variety not stated (VNS) seed but are more expensive. VNS seed should be purchased from a reputable dealer, be cleaned, tested for germination, and have a seed tag.
Fall Work
  • Soybean harvest—Harvest fields where cereal rye is to be planted as early as possible.
  • Tillage or no-tillage—To allow for adequate cover crop growth, it is best if no full-width tillage is planned after planting and before termination. If tillage is used, it is better to wait until spring in order to maintain surface cover to prevent erosion.
  • Timing of planting—Ideally, plant cereal rye as soon after harvest as possible and no later than one week after the 50% frost date. On average, plant before these dates: Upper Peninsula, Oct. 11; northern Lower Peninsula, Oct. 15; central Lower Peninsula, Oct. 25; and southern Lower Peninsula, Oct. 28. Use the Cover Crop Selector Tool (in Resources section) for more precise seeding dates for your county. Proximity to the Great Lakes and latitude influence these dates.
  • Planting method—Drill to 0.75–1.50 inches deep or broadcast with shallow incorporation. Good seed-soil contact will ensure a more reliable stand. See Recommended Cover Crop Seeding Methods and Tools (in Resources section).
  • Seeding rate—Drilled: 45–60 lbs./acre. Broadcast with shallow incorporation: 50–65 lbs./acre. These rates are based on high-quality seed with 85–98% germination.
  • Fertility or liming—If applying P, K, lime, or manure, complete the application and incorporation prior to seeding or apply to growing rye before the ground freezes. If injecting manure, low-disturbance injectors are available that will minimize damage to the cereal rye. Surface application of liquid manure on top of the rye is not recommended. Surface broadcast of dry manure should be done prior to seeding, but 4 tons or less can be applied to growing cereal rye with minimal damage provided it is evenly distributed.
Figure 1: Cereal rye growing after soybean (Paul Gross)
Figure 1: Cereal rye growing after soybean (Paul Gross)
Spring Work
  • Scouting—In the spring, scout your cover crop to determine growth and coverage (see Figure 1). If rainfall is below normal, monitor soil moisture in case earlier termination is needed.
  • Termination timing—Cereal rye usually grows rapidly in the spring, so have a termination plan ready. Terminate when plants are 6 to 12 inches tall and actively growing or about two weeks before planting corn—whichever comes first. Many growers successfully plant corn into terminated cereal rye taller than 12 inches, but new users should terminate when cereal rye is smaller. See Michigan State University Extension (MSUE) publication CC-01 in the Resources section for more information.
  • Termination by herbicide—Cereal rye can easily be terminated with full-rate glyphosate (minimum of 1 lb. acid equivalent [ae]/acre) after dormancy breaks. To maximize the effectiveness of glyphosate and minimize time for complete control, apply when rye is actively growing and temperatures favor growth. Larger rye, rye past the boot stage, or rye sprayed during cooler weather can be more difficult to kill or will die more slowly. Be aware that when conditions are cool and cloudy, atrazine and saflufenacil tank mixtures with glyphosate may delay or antagonize glyphosate activity for rye termination. See MSUE Bulletin E0434 (in Resources section) for more herbicide information.
  • Termination by tillage—In systems that include tillage or are organic, tillage can be a reliable termination method. However, multiple passes may be required. See MSUE publication CC-01 (in Resources section).
  • Termination modifications for dry weather—Watch the weather and be ready to modify your plans. In a dry spring, the cereal rye can use moisture needed by the cash crop, so terminate sooner to allow rainfall to make up the deficit.
  • Termination modifications for wet weather—When using herbicides to terminate cereal rye during a wet spring and under difficult conditions for spraying, be ready to use any break in the weather and/or low axle weight sprayers. If corn planting is less than 10 days away and the rye is tall, consider planting green (i.e., terminating within a day or two of planting). It is usually better to plant either into brown, dead rye plants or into standing green plants as opposed to large, dying, yellow/green (“rubbery”) cereal rye plants that have fallen on the soil surface and formed a mat. If utilizing tillage for termination, wait 10–14 days after rye incorporation to plant corn to avoid seed predation from seed corn maggot.
  • Starter fertilizer for corn after cereal rye—Since cereal rye can tie up nitrogen, reducing its availability to corn, we recommend a 2×2 application of a starter fertilizer with a rate of 30–50 pounds of actual N per acre.
  • Corn planting—It is usually best to no-till plant corn into the dead/dry or standing cereal rye cover crop. Almost all modern planters and drills are fully capable of planting corn into a cereal rye cover crop. Check planting depth and seed furrow closure shortly after beginning to plant into residue and adjust as needed.
  • Scouting—After planting, scout for corn emergence and population. Also, scout for weeds since substantial cereal rye residue can often delay emergence of annual weeds, which may delay the application of post-emergence herbicides.
Resources

Cover Crop Selector Tool —available from Midwest Cover Crops Council

Weed Control Guide for Field Crops (Michigan State University Extension Bulletin E0434)

Cover Crop Termination (Michigan State University Extension publication CC-01)

Recommended Cover Crop Seeding Methods and Tools (Agronomy Technical Note)— available from USDA–Natural Resources Conservation Service

Authors

Dean Baas, MSUE; Christina Curell, MSUE; Paul Gross, MSUE; Monica Jean, MSUE; Philip Kaatz, MSUE; and Elizabeth H. Schultheis, MSU (Note: This publication was adapted with consent from MCCC under a joint project to produce customized introductory guidance about cover crops for all member states/provinces.)

Reviewers and Contributors

Erin Hill, MSU; Eileen J. Kladivko, Purdue University; Anna L. Morrow, Midwest Cover Crops Council; Sieg Snapp, MSU

The Midwest Cover Crops Council (www.https://www.midwestcovercrops.org) aims to facilitate widespread adoption of cover crops throughout the Midwest by providing educational/outreach resources and programs, conducting new research, and communicating about cover crops to the public.
Funding for this project was provided by McKnight Foundation.

August 2019

The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable, sex, marital status, familial status, parental status, religion, sexual orientation, genetic information, political beliefs, reprisal, or because all or a part of an individual’s income is derived from any public assistance program. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program information (Braille, large print, audiotape, etc.) should contact USDA’s TARGET Center at (202) 720-2600 (voice and TDD). To file a complaint of discrimination write to USDA, Director, Office of Civil Rights, 1400 Independence Avenue, S.W., Washington, D.C. 20250-9410 or call (800) 795-3272 (voice) or (202) 720-6382 (TDD). USDA is an equal opportunity provider and employer. ©2019 by MCCC. All rights reserved.

Share

Midwest Cover Crops Council (MCCC-109)

Michigan State Extension (CC-03)


This publication is intended to provide a starting point for farmers who are new to growing cover crops. With experience, farmers may fine-tune the use of cover crops for their systems.

Introduction

This recipe provides an introductory approach to integrating a cover crop into a corn-soybean rotation. Planting a cereal rye cover crop ahead of soybean is a way to introduce cover crops into your rotation. (Note: Cereal rye [Secale cereale] and annual ryegrass [Lolium multiflorum] are different species and are not interchangeable.)

Planning and Preparation
  • Planning—Educate yourself. Start small. Be timely. Prioritize management based on your purpose and objectives.
  • Corn hybrid and planting—If possible, plant the preceding corn crop early and use an early maturity hybrid. One strategy is to use cover crops on the field you usually harvest first, on sloping ground, or on a field where you can watch it regularly.
  • Residual corn herbicides—Cereal rye can be seeded and successfully established in the fall following most spring-applied residuals used in corn. However, if cereal rye will be grazed or fed to livestock, check restrictions. See Weed Control Guide for Field Crops for more details.
  • Natural Resources Conservation Service (NRCS) programs—Cover crops enrolled in the Conservation Stewardship Program (CSP) or Environmental Quality Incentives Program (EQIP) cannot be used for dual-purpose grazing.
  • Seed purchase—Order cereal rye seed early. Named varieties generally perform more predictably and can produce substantially more growth than variety not stated (VNS) seed but are more expensive. VNS seed should be purchased from a reputable dealer, be cleaned, tested for germination, and have a seed tag.
Fall Work
  • Corn harvest—Harvest fields where cereal rye is to be planted as early as possible.
  • Tillage or no-tillage—To allow for adequate cover crop growth, it is best if no full-width tillage is planned after planting and before termination. If tillage is used, it is better to wait until spring in order to maintain surface cover to prevent erosion.
  • Timing of planting—Ideally, plant cereal rye as soon after harvest as possible and no later than one week after the 50% frost date. On average, plant before these dates: Upper Peninsula, Oct. 11; northern Lower Peninsula, Oct. 15; central Lower Peninsula, Oct. 25; and southern Lower Peninsula, Oct. 28. Use the Cover Crop Selector Tool for more precise seeding dates for your county. Proximity to the Great Lakes and latitude influence these dates.
  • Planting method—Drill to 0.75–1.50 inches deep or broad-cast with shallow incorporation. Good seed-soil contact will ensure a more reliable stand. See Recommended Cover Crop Seeding Methods and Tools.
  • Seeding rate—Drilled: 45–60 lbs./acre. Broadcast with shallow incorporation: 50–65 lbs./acre. These rates are based on high-quality seed with 85–98% germination.
  • Fertility or liming—If applying P, K, lime, or manure, complete the application and incorporation prior to seeding or apply to growing rye before the ground freezes. If injecting manure, low-disturbance injectors are available that will minimize damage to the cereal rye. Surface application of liquid manure on top of the rye is not recommended. Surface broadcast of dry manure should be done prior to seeding, but 4 tons or less can be applied to growing cereal rye with minimal damage provided it is evenly distributed.
Spring Work
  • Scouting—In the spring, scout your cover crop to determine growth and coverage. If rainfall is below normal, monitor soil moisture in case earlier termination is needed.
  • Termination timing—Cereal rye usually grows rapidly in the spring, so have a termination plan ready. Terminate when plants are 6 to 12 inches tall and actively growing or about two weeks before planting soybean—whichever comes first. Many growers successfully plant soybean into terminated cereal rye taller than 12 inches, but new users should terminate when cereal rye is smaller (Figure 1). See Michigan State University Extension (MSUE) publication CC-01 in the Resources section for more information.
Figure 1: Terminate cereal rye growth when approximately 6 inches in height (shown here). (Eileen Kladivko)
Figure 1: Terminate cereal rye growth when approximately 6 inches in
height (shown here). (Eileen Kladivko)
  • Termination by herbicide—Cereal rye can easily be terminated with full-rate glyphosate (minimum of 1 lb. acid equivalent [ae]/acre) after dormancy breaks. To maximize the effectiveness of glyphosate and minimize time for complete control, apply when rye is actively growing and temperatures favor growth. Larger rye, rye past the boot stage, or rye sprayed during cooler weather can be more difficult to kill or will die more slowly. Be aware that when conditions are cool and cloudy, metribuzin and saflufenacil tank mixtures with glyphosate may delay or antagonize glyphosate activity for rye termination. See MSUE Bulletin E0434 for more herbicide information.
  • Termination by tillage—In systems that include tillage or are organic, tillage can be a reliable termination method. However, multiple passes may be required. See MSUE publication CC-01.
  • Termination modifications for dry weather—Watch the weather and be ready to modify your plans. In a dry spring, the cereal rye can use moisture needed by the cash crop, so terminate sooner to allow rainfall to make up the deficit.
  • Termination modifications for wet weather—When using herbicides to terminate cereal rye during a wet spring and under difficult conditions for spraying, be ready to use any break in the weather and/or low axle weight sprayers. If soybean planting is less than 10 days away and the rye is tall, consider planting green (i.e., terminating within a day or two of planting). It is usually better to plant either into brown, dead rye plants or into standing green plants as opposed to large, dying, yellow/green (“rubbery”) cereal rye plants that have fallen on the soil surface and formed a mat. If using tillage for termination, wait 10–14 days after rye incorporation to plant soybean to avoid seed predation from seed corn maggot.
  • Soybean planting—It is usually best to no-till plant soybean into the dead/dry or standing cereal rye cover crop. Almost all modern planters and drills are fully capable of planting soybean into a cereal rye cover crop. Check planting depth and seed furrow closure shortly after beginning to plant into residue and adjust as needed.
  • Scouting—After planting, scout for soybean emergence and population. Additionally, scout for weeds since substantial cereal rye residue can often delay emergence of annual weeds, which may delay the application of post-emergence herbicides.
Resources

Cover Crop Selector Tool —available from Midwest Cover Crops Council

Weed Control Guide for Field Crops (Michigan State University Extension Bulletin E0434)

Cover Crop Termination (Michigan State University Extension publication CC-01)

Recommended Cover Crop Seeding Methods and Tools (Agronomy Technical Note)— available from USDA–Natural Resources Conservation Service,

Authors

Dean Baas, MSUE; Christina Curell, MSUE; Paul Gross, MSUE; Monica Jean, MSUE; Philip Kaatz, MSUE; and Elizabeth H. Schultheis, MSU (Note: This publication was adapted with consent from MCCC under a joint project to produce customized introductory guidance about cover crops for all member states/provinces.)

Reviewers and Contributors

Jerry Grigar, USDA–NRCS Service; Erin Hill, MSU; Eileen J. Kladivko, Purdue University; Anna L. Morrow, Midwest Cover Crops Council; Sieg Snapp, MSU

The Midwest Cover Crops Council (www.https://www.midwestcovercrops.org) aims to facilitate widespread adoption of cover crops throughout the Midwest by providing educational/outreach resources and programs, conducting new research, and communicating about cover crops to the public.
Funding for this project was provided by McKnight Foundation.

August 2019

The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable, sex, marital status, familial status, parental status, religion, sexual orientation, genetic information, political beliefs, reprisal, or because all or a part of an individual’s income is derived from any public assistance program. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program information (Braille, large print, audiotape, etc.) should contact USDA’s TARGET Center at (202) 720-2600 (voice and TDD). To file a complaint of discrimination write to USDA, Director, Office of Civil Rights, 1400 Independence Avenue, S.W., Washington, D.C. 20250-9410 or call (800) 795-3272 (voice) or (202) 720-6382 (TDD). USDA is an equal opportunity provider and employer. ©2019 by MCCC. All rights reserved.

Share

Jennifer Woodyard and Nathan Johanning – University of Illinois Extension; Shalamar Armstrong – Purdue University

February 2019

This publication is intended to provide a starting point for farmers who are new to growing cover crops. With experience, farmers may fine-tune the use of cover crops for their systems.


INTRODUCTION

The following recipe provides an introductory approach to integrating a cover crop into a corn-soybean rotation. Planting a cover crop ahead of a soybean cash crop is often the easiest way to introduce cover crops into your rotation.

PLANNING AND PREPARATION

– Planning—Educate yourself. Start small. Be timely. Prioritize management based on your purpose and objectives.

– Corn hybrid and planting—If possible, plant the preceding corn crop early and use an early maturity corn hybrid. One strategy is to use cover crops on the field you usually harvest first, on sloping ground, or on a field where you can watch it regularly, and to plant your earliest maturity hybrid on that field.

– Residual corn herbicides—Cereal rye can be seeded and a successful stand will occur in the fall following most of the spring-applied residuals used in corn. However, if cereal rye will be grazed or fed to livestock, there are some restrictions (see Resources section).

– Seed purchase—Order cereal rye seed early. Named varieties can produce substantially more growth or more predictable growth and maturity, but they are more expensive than VNS (variety not stated) seed. Start with VNS seed with a good germination rate purchased from a reputable seed dealer. Note that this means the seed has been cleaned, tested for germination, and has a seed tag even though it is VNS.

FALL WORK

– Corn harvest—Harvest fields where cereal rye is to be planted as early as possible.

– Tillage or no-tillage—To allow for adequate cover crop growth, it is best or easier if no full-width tillage is planned for after rye planting or before intended rye termination date. Thus, it is easier to integrate cover crops into no-till or strip-till systems.

– Timing of planting—Ideally, plant cereal rye as soon after harvest as possible and before two weeks after the 50% frost date. In northern Indiana, this would be before Nov. 10; in southern Indiana, before Nov. 25. Use the Selector Tool for more precise dates for your county.

– Seeding rate—Drilled seeding rate: 45–60 lbs./acre. Broadcast with shallow incorporation: 50–65 lbs./acre. These rates are based on high-quality seed with germination rates of 85–98%.

– Planting method—Drill to 0.75–1.50 inches deep or broadcast with shallow incorporation. An air-seeder mounted on a vertical tillage tool can also be used.

– Fertility or liming—If applying P, K, or lime, complete the application prior to the seeding operation or apply to the growing rye before the ground freezes. If it is necessary to inject manure, low-disturbance injectors are available that will cause minimal damage to the cereal rye. Surface application of liquid manure on top of the rye is not recommended. Surface broadcast of dry manure or litter should be done prior to seeding, but 4 tons or less can be applied to growing cereal rye with minimal damage by using modern spreading equipment that provides even distribution.

Figure 1: Terminate cereal rye growth when approximately 6 inches in height (shown here). (Eileen Kladivko)

SPRING WORK

– Scouting—In the spring, scout your cereal rye cover crop to determine how well it is growing and its coverage. But if rainfall is below normal, scout also to monitor soil moisture in case earlier termination is needed.

– Termination timing—Terminate the cereal rye in the spring when plants are 6 to 12 inches tall and actively growing or about two weeks before planting soybean— whichever comes first. Many growers will successfully plant soybean into terminated cereal rye much taller than 12 inches, especially if weed control is a primary purpose, but new cover crop users should terminate when the cereal rye is smaller (see Figure 1).

– Termination herbicide—Cereal rye can easily be terminated with a full rate of glyphosate (minimum of 1 lb. acid equivalent [ae]/acre) after dormancy breaks in the spring. Effectiveness and rapidity of termination improves if rye is rapidly growing and air temperatures are warmer. Larger rye, rye past the boot stage, or rye sprayed during cooler weather can be more difficult to kill or will die more slowly. Be careful of metribuzen and metribuzen premixes antagonizing glyphosate if weather is cool and cloudy near the application date.

– Termination modifications for dry weather—Watch the weather and be ready to modify your termination plans. In a dry spring, the cereal rye cover crop has the potential to use moisture that the cash crop will need, so terminate cover crops sooner to allow rainfall to make up the deficit.

– Termination modifications for wet weather—In a wet spring, when it has been very difficult to get into the fields to spray, be ready to take advantage of any break in the weather and/or use low axle weight sprayers. If projected soybean planting is less than 10 days away and the rye is tall, then it often works better to spray within a day or two of planting. It is usually better to plant either into brown, dead rye plants or into standing green plants rather than into large, dying, yellow/green (“rubbery”) cereal rye plants that have fallen on the soil surface and formed a mat. See Purdue Extension publication AY-353-W (in Resources section) for more details.

– Soybean planting—It is usually best to no-till plant soybean into the dead/dry or standing cereal rye cover crop. Almost all modern planters and drills are fully capable of planting soybean into a cereal rye cover crop. Check planting depth and seed furrow closure shortly after beginning to plant into the cover crop residue as usually some adjustments are needed.

– Scouting—After soybean planting, scout for soybean emergence and population. Additionally, scout for weeds since substantial cereal rye residue can often delay emergence of annual weeds, which may delay the application of post-emergence herbicides.

RESOURCES

Cover Crop Selector Tool  — available from the Midwest Cover Crops Council
Managing Cover Crops: An Introduction to Integrating Cover Crops into a Corn-Soybean Rotation (Purdue Extension publication AY-353-W)
Residual Herbicides and Fall Cover Crop Establishment (Purdue Extension Weed Science publication)
Terminating Cover Crops: Successful Cover Crop Termination with Herbicides (Purdue Extension publication WS-50-W)
Recommended Cover Crop Seeding Methods and Tools (Agronomy Technical Notes)—available from the USDA–Natural Resources Conservation Service

AUTHORS

Eileen Kladivko, Purdue University; Shalamar Armstrong, Purdue University; and Anna Morrow, Midwest Cover Crops Council

REVIEWERS AND CONTRIBUTORS

Marisol Berti, North Dakota State University; Barry Fisher, USDA-NRCS; William Johnson, Purdue University; Tom Kaspar, USDA–Agricultural Research Service (retired); DeAnn Presley, Kansas State University; Vaughn Sothman, Sharp Brothers Seed Co., Kansas; and Anne Verhallen, Ontario Ministry of Agriculture, Food and Rural Affairs

THE MIDWEST COVER CROPS COUNCIL (WWW.HTTPS://WWW.MIDWESTCOVERCROPS.ORG) AIMS TO FACILITATE WIDESPREAD ADOPTION OF COVER CROPS THROUGHOUT THE MIDWEST BY PROVIDING EDUCATIONAL/OUTREACH RESOURCES AND PROGRAMS, CONDUCTING NEW RESEARCH, AND COMMUNICATING ABOUT COVER CROPS TO THE PUBLIC.
FUNDING FOR THIS PROJECT WAS PROVIDED BY MCKNIGHT FOUNDATION.

Revised May 2019

The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable, sex, marital status, familial status, parental status, religion, sexual orientation, genetic information, political beliefs, reprisal, or because all or a part of an individual’s income is derived from any public assistance program. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program information (Braille, large print, audiotape, etc.) should contact USDA’s TARGET Center at (202) 720-2600 (voice and TDD). To file a complaint of discrimination write to USDA, Director, Office of Civil Rights, 1400 Independence Avenue, S.W., Washington, D.C. 20250-9410 or call (800) 795-3272 (voice) or (202) 720-6382 (TDD). USDA is an equal opportunity provider and employer. ©2019 by MCCC. All rights reserved.

Share

Midwest Cover Crops Council (MCCC-104)

Iowa State University Extension (CROP 3159)


This publication is intended to provide a starting point for farmers who are new to growing cover crops. With experience, farmers may fine-tune the use of cover crops for their systems.

Introduction

The following recipe provides an introductory approach to integrating a cover crop into a soybean-corn rotation. Often the easiest place to begin is to plant a cover crop ahead of a soybean cash crop following corn, so consider starting with the companion recipe titled Post Corn, Going to Soybean: Use Cereal Rye (publication MCCC-103; see Resources).

Planning and Preparation
  • Planning—Read about cover crops. Go to field days. Start small. Be timely. Prioritize management based on purpose and objectives.
  • Soybean cultivar and planting—If possible, plant preceding soybean crop early and use an early-maturity-group cultivar. Some possible strategies are to try cover crops in a field that is usually harvested first, on sloping ground, or where you plan to plant your earliest-maturity-group soybean cultivar.
  • Residual soybean herbicides—Oats can be planted in the fall and produce a successful stand following spring application of most residual soybean herbicides. If the oats are grazed, there are some time-interval restrictions. (See Resources.)
  • Seed purchase—Order oat seed early, usually by early August. Named oat varieties can produce substantially more growth, but they are usually more expensive than VNS (variety not stated) seed. Use good quality seed that has been cleaned, tested for germination and weed seed contamination, and purchased from a reputable seed dealer.
Fall Work
  • Soybean harvest—Harvest fields where oats are to be planted as early as possible. This is not as critical if cover crops are seeded before harvest.
  • Tillage or no-tillage—Generally, it is easier to integrate cover crops into no-till or strip-till systems. If full-width tillage is planned, it should be delayed until after the oats are killed by freezing in late fall to allow time for oat cover crop growth. Usually it is more desirable to delay tillage until spring to maintain surface cover and prevent erosion.
  • Timing of planting—Oats are relatively frost tolerant but are not winter hardy. In general, oats will grow well in the fall if they are planted at least six weeks before the average hard frost date (28ºF). To allow for adequate growth, in northern Iowa this should be before September 9; in central Iowa, before September 16; and in southern Iowa, before September 23. (See Cover Crop Management publication in Resources.)
  • Seeding rate—Minimum seeding rate: 60 lbs./acre. Beginners should consider higher seeding rates for broadcast seeding methods with or without incorporation. Note that these rates assume the seed will have germination rates greater than 85%.
  • Planting method—Aerial seed with a plane or helicopter or broadcast/drop seed with a ground-based vehicle into the standing soybean crop. In most of Iowa, aerial or broadcast seeding should take place in late August and/or just before soybean leaves begin to yellow. Rainfall after seeding is essential for establishment, but normal average weekly rainfall totals in Iowa decrease as fall progresses, so in most years, it is usually better to seed late in August rather than wait for leaf yellowing.
  • Alternative planting method—Drill to a depth of 0.75–1.50 inches or broadcast with shallow incorporation to less than 1.50 inches immediately after soybean harvest but before recommended dates above. For this method, the seeding rate is also 60 lbs./acre.
  • Scouting—In the fall, scout your oat cover crop to determine how well it is growing and its coverage.
  • Fertility or liming—Surface applying P, K, or lime before the ground freezes can be done without harming the cover crop too much if the soil is not too wet, although some damage will occur in the wheel tracks. If P, K, or N fertilizer, or manure is injected in the fall, it is usually best to wait until after the cover crop has winter-killed. In this case, use a low-disturbance applicator to minimize incorporation of surface residues.
Figure 1: Dead oat cover crop residue in the spring after oats and some radishes were drilled following an early soybean harvest in Indiana (Eileen Kladivko)
Figure 1: Dead oat cover crop residue in the spring after oats and some radishes were drilled following an early soybean harvest in Indiana (Eileen Kladivko)
Spring Work
  • Scouting before planting—In the spring, scouting relative to the cover crop is usually not needed because it has winter-killed.
  • Termination—Unlike overwintering cover crops, oats winter-kill, so termination is not needed.
  • Corn planting—Almost all modern row planters are fully capable of planting corn into a dead oat cover crop and soybean residues without preplant tillage. Row cleaner attachments can sometimes be beneficial to increase soil warming. As usual, check planting depth and seed furrow closure shortly after beginning to plant because some adjustments may be needed with higher residue levels.
  • Starter fertilizer—If N fertilizer has not been applied before planting, consider equipping your corn planter with a 2×2 starter fertilizer applicator and aim for a starter fertilizer rate between 30–50 pounds of actual N per acre.
  • Scouting after planting—As usual, scout for corn emergence, population, and insect pests after planting. Additionally, scout for weeds because substantial oat and soybean residue may delay emergence of annual weeds, which may then delay the application of post-emergence herbicides.
Resources

Cover Crop Selector Tool — available from the Midwest Cover Crops Council

Cover Crop Management (Iowa Agronomy Technical Note 38)—available from the USDA Natural Resources Conservation Service

Effect of residual herbicides on cover crop establishment (Iowa State Extension and Outreach Integrated Crop Management Encyclopedia Article)

Post Corn, Going to Soybean: Use Cereal Rye (Iowa Cover Crop Recipe series, MCCC-103)—available from the Midwest Cover Crops Council

Authors

Tom Kaspar, USDA-ARS (retired); Mark Licht, Iowa State University (Note: This publication was adapted with consent from MCCC under a joint project to produce customized introductory guidance about cover crops for all member states/provinces.)

Reviewers and Contributors

Shalamar Armstrong, Purdue University; Marisol Berti, North Dakota State University; Eileen Kladivko, Purdue University; Keith Kohler, USDA-ARS; Anna Morrow, Midwest Cover Crops Council; DeAnn Presley, Kansas State University; Vaughn Sothman, Sharp Brothers Seed Co., Kansas; and Anne Verhallen, Ontario Ministry of Food and Agriculture

Acknowledgments

This publication was developed with contributions and collaboration from Iowa Learning Farms and Practical Farmers of Iowa.

The Midwest Cover Crops Council (www.https://www.midwestcovercrops.org) aims to facilitate widespread adoption of cover crops throughout the Midwest by providing educational/outreach resources and programs, conducting new research, and communicating about cover crops to the public.
Funding for this project was provided by McKnight Foundation.

Revised May 2019

The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable, sex, marital status, familial status, parental status, religion, sexual orientation, genetic information, political beliefs, reprisal, or because all or a part of an individual’s income is derived from any public assistance program. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program information (Braille, large print, audiotape, etc.) should contact USDA’s TARGET Center at (202) 720-2600 (voice and TDD). To file a complaint of discrimination write to USDA, Director, Office of Civil Rights, 1400 Independence Avenue, S.W., Washington, D.C. 20250-9410 or call (800) 795-3272 (voice) or (202) 720-6382 (TDD). USDA is an equal opportunity provider and employer. ©2019 by MCCC. All rights reserved.

Share

Midwest Cover Crops Council (MCCC-103)

Iowa State University Extension (CROP 3158)


This publication is intended to provide a starting point for farmers who are new to growing cover crops. With experience, farmers may fine-tune the use of cover crops for their systems.

Introduction

The following recipe provides an introductory approach to integrating a cover crop into a corn-soybean rotation. Planting a cover crop ahead of a soybean cash crop is often the easiest way to introduce cover crops into your rotation.

Planning and Preparation
  • Planning—Read about cover crops. Go to field days. Start small. Be timely. Prioritize management based on purpose and objectives.
  • Corn hybrid and planting—If possible, plant preceding corn crop early and use an early maturity hybrid. Possible strategies are to use cover crops in a field that is usually harvested first, on sloping ground, or where you plan to plant your earliest maturity hybrid, corn silage, or seed corn.
  • Residual corn herbicides—Cereal rye can be planted in the fall and produce a successful stand following most spring-applied residual corn herbicides. If cereal rye is grazed or harvested for forage, there are some time-interval restrictions. (See Resources.)
  • Seed purchase—Order cereal rye seed early, usually by early August. Named rye varieties can produce substantially more growth and have predictable development, but they are usually more expensive than VNS (variety not stated) seed. Use good quality seed that has been cleaned, tested for germination and weed seed contamination, and purchased from a reputable seed dealer.
Fall Work
  • Corn harvest—Harvest fields where cereal rye is to be planted as early as possible.
  • Tillage or no-tillage—Generally, it is easier to integrate cover crops into no-till or strip-till systems. If full-width tillage is planned, do it immediately after corn harvest or delay it until after the planned cover crop termination date in the spring to allow time for cover crop growth.
  • Timing of planting—Ideally, plant cereal rye as soon as possible after corn harvest and before two weeks after the average hard frost date (28˚F). In northern Iowa, this would roughly be before October 21; in central Iowa, before October 28; and in southern Iowa, before November 7. (See Cover Crop Management publication in Resources).
  • Seeding rate—Minimum seeding rate: 45 lbs./acre. Beginners should consider 55 lbs./acre for drilled seed and 61 lbs./acre for shallow incorporation. Note that these rates assume the seed will have germination rates greater than 85%.
  • Planting method—Drill to a depth of 0.75–1.50 inches or broadcast with shallow incorporation to less than 1.50 inches.
Figure 1: Cereal rye cover crop planted following corn in late April on the Steve Berger farm in Iowa (Tom Kaspar)
Figure 1: Cereal rye cover crop planted following corn in late April on the Steve Berger farm in Iowa (Tom Kaspar)
Spring Work
  • Scouting before planting—In the spring, scout your cereal rye cover crop to determine how well it is growing and its coverage. If rainfall is below normal, then scout to monitor soil moisture in case earlier cover crop termination is needed.
  • Termination timing—Terminate the cereal rye in spring when the plants are 6 to 12 inches tall and actively growing or more than 10 days before planting soybean—whichever comes first. Many experienced cover crop users will successfully terminate cereal rye much taller than 12 inches or less than 10 days before planting, but termination and planting may be more difficult for new users.
  • Termination herbicide—Cereal rye can easily be terminated with a full rate of glyphosate (1 lb. acid equivalent/acre) after the rye begins growing in the spring. Effectiveness and rapidity of termination improves if rye is rapidly growing and air temperatures are warmer (> 60˚F). Larger rye, rye past the boot stage, or rye sprayed during cooler weather can be more difficult to kill, may require higher glyphosate rates, or will die more slowly. Use best management practices for glyphosate to improve effectiveness.
  • Termination modifications for wet weather—In a wet or windy spring, when it has been very difficult to get into the fields to spray, be ready to take advantage of any break in the weather and/or use low axle weight sprayers. If projected soybean planting is less than 10 days away and the rye is tall, then it often works better to spray a day or two before planting. Crop insurance requires that cover crops be terminated at the very latest by five days after soybean planting in the southeastern two-thirds of Iowa and before soybean planting in the northwestern one-third of Iowa.
  • Soybean planting—It is usually easiest to no-till plant soybean into the dead, brown cereal rye cover crop. Almost all modern row planters and drills are fully capable of planting soybean into a dead cereal rye cover crop. If wet or windy weather has delayed cereal rye termination, it is usually better to plant into standing green plants rather than into large green plants that are dying and have fallen on the soil surface, forming a mat. For either scenario, check planting depth and seed furrow closure shortly after beginning to plant because some adjustments are usually needed.
  • Scouting after planting—Scout for soybean emergence, population, and insect pests. Additionally, scout for weeds because substantial cereal rye residue often can delay emergence of annual weeds, which may then delay the application of post-emergence herbicides.
Resources

Cover Crop Selector Tool  — available from the Midwest Cover Crops Council

Cover Crop Management (Iowa Agronomy Technical Note 38)—available from the USDA Natural Resources Conservation Service

Effect of residual herbicides on cover crop establishment (Iowa State Extension and Outreach Integrated Crop Management Encyclopedia Article)

NRCS Cover Crop Termination Guidelines: Non-Irrigated Cropland—available from the USDA Natural Resources Conservation Service

Post Soybean, Going to Corn: Use Oats (Iowa Cover Crop Recipe series, MCCC-104)—available from the Midwest Cover Crops Council

Authors

Tom Kaspar, USDA-ARS (retired); Mark Licht, Iowa State University (Note: This publication was adapted with consent from MCCC under a joint project to produce customized introductory guidance about cover crops for all member states/provinces.)

Reviewers and Contributors

Shalamar Armstrong, Purdue University; Marisol Berti, North Dakota State University; Eileen Kladivko, Purdue University; Keith Kohler, USDA-ARS; Anna Morrow, Midwest Cover Crops Council; DeAnn Presley, Kansas State University; Vaughn Sothman, Sharp Brothers Seed Co., Kansas; and Anne Verhallen, Ontario Ministry of Food and Agriculture

Acknowledgments

This publication was developed with contributions and collaboration from Iowa Learning Farms and Practical Farmers of Iowa.

The Midwest Cover Crops Council (www.https://www.midwestcovercrops.org) aims to facilitate widespread adoption of cover crops throughout the Midwest by providing educational/outreach resources and programs, conducting new research, and communicating about cover crops to the public.
Funding for this project was provided by McKnight Foundation.

Revised May 2019

The U.S. Department of Agriculture (USDA) prohibits discrimination in all its programs and activities on the basis of race, color, national origin, age, disability, and where applicable, sex, marital status, familial status, parental status, religion, sexual orientation, genetic information, political beliefs, reprisal, or because all or a part of an individual’s income is derived from any public assistance program. (Not all prohibited bases apply to all programs.) Persons with disabilities who require alternative means for communication of program information (Braille, large print, audiotape, etc.) should contact USDA’s TARGET Center at (202) 720-2600 (voice and TDD). To file a complaint of discrimination write to USDA, Director, Office of Civil Rights, 1400 Independence Avenue, S.W., Washington, D.C. 20250-9410 or call (800) 795-3272 (voice) or (202) 720-6382 (TDD). USDA is an equal opportunity provider and employer. ©2019 by MCCC. All rights reserved.

Share

Subscribe to our ListServ

Sign up to receive the latest MCCC news and updates!